The vacuum layer is what makes this work: with almost nothing left to conduct heat away, hot food stays above serving temperature through a working day, and in the larger sizes you can pour in boiling water and raw rice in the morning and open cooked congee at lunch.
The detail behind that claim: A mouth wide enough for a serving spoon, which decides whether it works for solid food. Sized to be held and opened one-handed. A base that grips rather than slides when the lid is twisted. Stock colours that ship mixed, so a retailer can test the range before committing. The interior wipes clean without scrubbing, which matters more on a food container than on a drinks bottle. The base grips a smooth table instead of sliding when the lid is twisted. The finish reads as a considered product in the hand, not a commodity one.
Also on the buyer’s checklist here: the body finish, inner liner, easy to clean, outdoor use, base, non-slip.
Also cited on repeat orders: appearance, in stock, peak season, restock cadence.
Choosing between them
How TW-1006 compares with the rest of the range
Buyers rarely arrive knowing which model they want — they arrive knowing the brief. This table is the fastest way to check whether TW-1006 is the right answer or whether a sibling fits better. The row highlighted is the one you are looking at. Every model listed runs from 500 pieces per design.
Every model above ships from 500 pieces per design. Mixing several of them in one container is normal — a 20ft container holds roughly 26 m³ of cartons, so a mixed load is planned on carton volume rather than on piece count. Send the full list at enquiry rather than model by model.
Who is buying TW-1006, and what they do with it
A mother-and-baby retailer in São Paulo, Brazil takes this one for parents with young children. Worth noting how they buy: they reorder in small frequent batches rather than one large drop; and ordering in volume.
Also on the buyer’s checklist here: parents, high volume, restock cadence.
The use cases behind the orders: a commute where there is no microwave at the other end; baby food carried warm rather than reheated; porridge that finishes cooking on the way; soup; a packed meal; camping and days out; iced drinks in summer. The spread matters commercially: a model that only suits one of these is a harder listing to justify.
Also on the buyer’s checklist here: parents, baby food, heat retention, porridge, office workers, commuting, students, packed meals, outdoor use.
A job worth mentioning: A buyer in Brazil placed a large single order with their own logo printed timed to a seasonal peak. We ran the line on overtime and moved their batch up the queue, running printing in parallel rather than in sequence. They have reordered since. We would rather show a job that stretched us than a routine one, because the routine ones tell you nothing about what happens when something goes wrong.
Also in play on that job: high volume, custom decoration, peak season, expedited production, reorder.
Importers & wholesalers
This model packs 30 per carton (62cm×47cm×66cm for the base size — the full carton table is in the spec above), and that number decides how many pieces fit a 20ft container far more than the FOB price does. What decides your landed cost here is the carton, not the unit price: ask for the container plan before you fix a retail price, because a wide-body jar fills a 20ft on volume long before it hits the weight limit. We quote EXW Yongkang, FOB Ningbo or Shanghai, or DDP door to door, and we will say which of the three costs you least given where you are rather than defaulting to whichever is easiest for us.
Brand owners & private label
On TW-1006 the stock range is 3 colours (blue, pink, orange), so a Pantone match is only worth the 1,000-piece run if none of those is close enough. Budget it as three lines, not one: decoration sits inside the unit price, a matched Pantone is its own spray run from 1,000 pieces, and packaging is separate with its own tooling and proofing round. Brands that budget these as a single number are the ones surprised at quotation: decoration sits in the unit price, a matched Pantone is a separate spray run from 1,000 pieces, and a printed colour box carries its own tooling and one proofing round. We sign an NDA before you share artwork, and a shape you tool for stays reserved to you — the same terms we have run with Hallmark since 2017 and with KRAUS for over ten years.
Retail chains
TW-1006 packs 30 per carton, so a 12-store drop lands on a clean carton multiple rather than a split case. Retail-ready means more than a colour box: UPC or EAN printed and scan-tested before the carton is sealed, carton marking to your own packaging manual, and inner counts that match what your DC expects. A barcode that fails at the till becomes a chargeback, and it is entirely preventable at our end: we print and scan-test every UPC or EAN before the carton is sealed. Ask for the retail packaging spec sheet with your first quote — it lists carton dimensions, inner counts and the UPC placement we scan-test before sealing.
Promotional distributors
TW-1006 is a single-capacity line, which is the fastest thing we can turn around when a date is already tight. Work backwards from the in-hands date, not forwards from the order date: 7–10 days for a pre-production sample, about 30 days production after approval, then 30–35 days sea freight to Europe or 25–30 to the US west coast. Production is 30 days after deposit and artwork approval, plus 7–10 days for a printed pre-production sample, plus sea freight — roughly 30–35 days to Europe, 25–30 to the US west coast. Late artwork is normal in this business; a date discovered late is not survivable — artwork approval is what starts the 30-day production clock, not the deposit. Tell us the date at enquiry and we will say honestly whether it is achievable.
Amazon & e-commerce sellers
TW-1006 ships in a 62 cm × 47 cm × 66 cm carton — send us your FBA plan and we will confirm whether that splits cleanly under the dimension cap before you book. FNSKU labels, Prop 65 and suffocation warnings applied here, cartons built to FBA dimension limits, and we can split a shipment across fulfilment centres if you send the plan. Doing it at the factory removes a prep-centre handling fee and about a week of transit on every restock. Watch dimensional weight on this category — the carton is light for its size, so FBA usually bills on volume.
End users & institutions
On TW-1006 laser engraving is the safe call for daily institutional washing. Canteens, schools and site catering wash hard and often, and this category goes through more of it than a drinks bottle because it holds food. Laser engraving costs slightly more up front and removes the complaint entirely: the mark is cut into the steel and reads the same after a season of commercial dishwashing, while printed artwork on a coated body visibly fades.
Failures we hear about from buyers who switch to us
The complaints below come from buyers who arrived here after a bad run elsewhere. Ask any supplier about them directly — the way they answer tells you more than the answer.
✓
Base grips glued on badly
The non-slip ring falls off in transit or after a few washes, and then the container slides across a table. A small part, but it is the one customers photograph in complaints.
✎
Incomplete vacuum draw
A body that was not fully evacuated performs like a plain double wall — noticeably worse, but only after the customer has owned it a while. We test every body before it is assembled.
⚑
Importers & wholesalers
— Workable from 500 pieces per design. At 30 pcs per 62cm×47cm×66cm carton, a 20ft container takes roughly 4,000 pieces of this model alone — worked from the biggest of this model’s carton sizes, and confirmed on the pro forma once the load plan is fixed. Tell us the full model list at enquiry rather than one at a time — the quote changes when several models share a colour run or a carton size.
◷
Brand owners & private label
— Yes. Three separate lines to budget: the logo sits in the unit price, a matched Pantone is its own run at 1,000 pieces, and packaging is third — this model ships in a printed colour box as standard, and anything else is a separate tooling and proofing round.
☑
End users & institutions
— Suited to schools and campus retail. For institutional buying, specify laser engraving rather than print — a printed logo on a coated body typically fades within one season of daily commercial dishwashing, while an engraved mark is cut into the 304 steel and does not.
Where TW-1006 is actually made
Eight workshops in Yongkang, Zhejiang, running since 1998 — mould development, vacuum welding, injection moulding, spray painting, laser marking, printing, assembly, inspection and packing, all in one building. For TW-1006 the stage worth watching is the vacuum draw and the wide-mouth seal.
A food jar is harder to build than a drinks flask for one reason: the mouth is wide, so the sealing surface is long and the liner has a bigger opening to close around. We draw the vacuum on the liner as a semi-finished part and test it there — before assembly, before coating, before your logo goes on. A weak draw passes a same-day test and fails two months later, and on a finished, printed, shipped jar that flaw is invisible until it is your customer’s problem. The second bench that matters is the inverted seal test: liquid in, lid on, upside down. We run it because a jar that seeps congee into a laptop bag is returned once and never bought again.
We inspect 8% of every batch rather than a fixed sample per shipment. Buyers are welcome on site — eight workshops in Yongkang, Zhejiang, running since 1998, about three hours by road from Ningbo port and two from Hangzhou airport, which makes a factory visit a realistic side trip rather than a separate journey. Ask to see that bench specifically; it is where the difference shows — we check vacuum integrity on 100% of bodies at the semi-finished stage, before assembly and coating, because a micro-leak is undetectable once the jar is built.
Is TW-1006 the right one for your programme?
Importers & wholesalers — Workable from 500 pieces per design. At 30 pcs per 62cm×47cm×66cm carton, a 20ft container takes roughly 900 pieces of this model alone. Tell us the full model list at enquiry rather than one at a time — the quote changes when several models share a colour run or a carton size.
Brand owners & private label — Yes. Three separate lines to budget: the logo sits in the unit price, a matched Pantone is its own run at 1,000 pieces, and packaging is third — this model ships in a printed colour box as standard, and anything else is a separate tooling and proofing round.
End users & institutions — Suited to schools and campus retail. For institutional buying, specify laser engraving rather than print — a printed logo on a coated body typically fades within one season of daily commercial dishwashing, while an engraved mark is cut into the 304 steel and does not.
FAQ
Ordering TW-1006 — common questions
Why TW-1006 rather than another model in this range?▾
This one runs 500 ml. End users are office workers carrying a hot lunch, commuters, parents carrying baby food and warm porridge, baby and toddler food, students and school lunches. If that does not describe your programme, send us the brief instead of the model number — picking from a catalogue is how buyers end up with the wrong one.
How long does TW-1006 keep food hot?▾
At 500 ml, expect around 8 hours with a full fill, less if it is opened repeatedly or only half filled. The double-wall 304 stainless body is the reason: with the air drawn out between the walls there is almost nothing left to conduct heat away. Two habits worth printing on your packaging — rinse with boiling water before filling, and fill it as close to the top as practical.
Which colours can we order TW-1006 in?▾
Stock colours are blue, pink, orange — those run from 500 pieces per design. A matched Pantone is a separate spray or resin run and starts at 1,000 pieces. Mixed-colour containers are normal here: several buyers deliberately split a container across colours to see which ones move before committing to one.
How do we brand TW-1006?▾
For a brand colour we spray the body first and print onto the coating — two operations rather than one, so it shows in the price. For a mark that never wears, laser straight into the steel. Which is right depends entirely on whether the product lives on a desk or behind a bar.
What is the MOQ, lead time and carton spec for TW-1006?▾
Minimum is 500 per design, or 1,000 if you need the colour matched rather than chosen from stock. Production runs 30 days after deposit and artwork approval, sample in 7–10 days. Packing is 30 pcs per carton at 62cm × 47cm × 66cm. Our plant is about three hours from Ningbo port, so FOB Ningbo is usually the cleanest route; EXW and DDP are both available.
Get a quote on TW-1006
Tell us the quantity, colours and how you want the logo applied — we reply within 24 hours, Monday to Saturday.
More food jars
Compare with similar models to find your exact match
